WAENLIR Two Position Stainless Steel Flag Pole Holder, Heavy Duty and Rust Free Flag Mounting Bracket for House(1" Inner Diameter) 4.8 out of 5 stars 186 $20.99 $ 20 . 99
:stainless steel mounting bracketsAlise 10 Pcs Stainless Steel Flat Straight Brace Brackets Solid Mending Plates Repair Fixing Replacement,3-4/5 Inch Brushed Finish 4.7 out of 5 stars 231 $9.99 $ 9 . 99
The inner, pole-side clamp section is tapped to accept a 5/8" diameter bolt an includes a curved surface with spurs to penetrate into the pole and provide a stable installation The design provides a 1-5/8" clearance from the surface of the pole to the cable and 3-3/4" clamping surface length. Material:Hot Dipped Galvanized, Ductile Iron
Banding Components Line Construction Hardware Power Banding 1 1/4" x .04" x 100' used to secure brackets and equipment to poles. Skived edges to remove burrs. Use in conjunction with buckle PSC2080562.
Cross Arm Braces & Brackets - Power Manufacturing*Made from 1/4 x 3 Stainless Steel Type 316 flat bar. *Used for adapting transformer lugs to single bolt on cluster. *Two plates required per transformer. Bayonets, Ground Wire. For supporting overhead ground wire on wood or steel poles. Bayonets have an 11/16 hole and an 11/16 pole-mounting slot to allow for inaccuracy in boring holes.
From the Ground Up Meeting all your Pole Line Hardware needs! Select from a variety of quality vendors. Check out the Mile Estimator on page A-16 8-Way Expanding Anchors - Covers 70-115-135-200 sq. in. Anchor Rods - 5/8" rod diameter 5'-6'-7'-8' thimbleye and twineye Angled Thimbleye - 5/8" and 10"-12"-14"-16" lengths
Insulators - Pole Line HardwareInsulated Clevis Hubbell 0340 HUB-0340 Insulated Clevis Standard, Material:Steel, Clevis Type.11/16 Mount Hole Clevis Pin Diameter:5/8 IN, Clevis Size:5 IN Length X 1-1/2 IN Width X 3-5/16 IN Height, Finish:ASTM A-153 Galvanized, Mounting:11/16 X 3/4 IN Oval, Material Size:3/16 IN X 1-1/2 IN, Standards:ANSI C135.20
Jocelyn Forge Inc. - Pole Line HardwareJocelyn Guy Attachment provide an economical and efficient means of fastening guy to pole, either steel or wood poles. The press formed steel guy attachment has a well rounded strand groove that would protect the strand from damage. The G1051 are used with 4-inch wide universal pole band.
Manufacturers, Suppliers of Adjustable Plate, Pole Line Hardware Fittings,Power Transmission Line Hardware,Insulator Hardware,Steel Forged Hardware from India. +91-22-28547870 /
Pole Line Hardware A-I > MacLean Power SystemsPole Line Hardware A-I When it comes to Pole Line Hardware, MacLean Power has a depth of knowledge and manufacturing experience that is unsurpassed in the market. These pages detail the hardware needed for power utility applications.
Protective grounding requirements for transmission and
Grounding on Metal Transmission StructuresGrounding on Wood Pole Transmission StructuresTransmission Line Terminal Ground SwitchesGrounding on Distribution LinesSurface Equipment and Vehicle GroundingGrounding Insulated Power Cable1.1 Lattice Steel Structures The preferred method for installing grounds on higher voltage single-circuit lattice steel transmission line structures, where the conductors are a greater distance from the structure than those on lower voltage structures, is to install them from the bridge above the conductors(see Figure 2). On double-circuit lattic1.2 Slip Joint Steel Pole Structures Slip joint structures either have bonding cables permanently attached to each joint or joint resistance should be measured on selected structures after installation and periodically as maintenance personnel deem necessary. Surfaces where protective grounds are to be attached must be cleaned prior to cable 1.3 Weathering Steel Pole Structures The highly resistive protective oxideon weathered steel should not be removed. Protective grounding is best accomplished by welding a copper or steel bar or stainless steel nut to which a threaded copper stud can be inserted at each grounding location. Weathering steel poles should be constructed with bonds bMounting Hardware Dori PoleDesigned for the 12 JR Dori Pole only, the JR Mounting plate attaches to any flat surface. This 5 x 5 black coated steel plate is intended to be bolted or lag bolted to the side of rafts or docks. This is also a suggested installation method for deterring geese and assorted birds from rafts.